D.P. Engineers

Dwyer Maghnehic Gauge in Lakhimpur Kheri Uttar Pradesh
SERIES 2000 MAGNEHELIC® DIFFERENTIAL PRESSURE GAGESIndicate Positive, Negative or Differential, Accurate within 1%No Power RequiredLow CostUsed in Isolation/ Hospital Environments and Temporary Units (No Power Required)Select The Series 2000 Magnehelic® Gage For a Versatile Low Differential Pressure Gage With a Wide Choice of 81 Models And 27 Options To Choose From. Using Dwyer’s Simple, Frictionless Magnehelic® Gage Movement, It Quickly Indicates Air Or Noncorrosive Gas Pressures--Either Positive, Negative (Vacuum) or Differential. The Design Resists Shock, Vibration, Over-Pressures And is Weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage Option For An Accuracy Within 1% of Full Scale, Located Below in the Product Configurator. Also Included With The –HA Option At No Extra Cost Are a Mirrored Scale Overlay and a 6 Point Calibration Certificate.NIST CALIBRATION Available In Product Configurator.Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Please See Series AT-2000 for ATEX Approved.PRODUCT APPLICATIONSFilter MonitoringAir Velocity with Dwyer Pitot TubeBlower Vacuum MonitoringFan Pressure IndicationDuct,Room or Building PressuresClean Room Positive Pressure IndicationSPECIFICATIONSService:Air And Non-Combustible, Compatible Gases (Natural Gas Option Available).Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Wetted Materials:Consult Factory.Housing:Die Cast Aluminum Case And Bezel, With Acrylic Cover, Exterior Finish is Coated Gray To Withstand 168 Hour Salt Spray Corrosion Test.Accuracy:±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM Ranges), Throughout Range at 70°F (21.1°C).Pressure Limits:-20 in Hg. to 15 PSIG.† (-0.677 bar to 1.034 bar); MP Option: 35 PSIG (2.41 Bar), HP Option: 80 PSIG (5.52 Bar).Enclosure Rating:IP67.Overpressure:Relief Plug Opens At Approximately 25 PSIG (1.72 Bar), Standard Gages Only. See Overpressure Protection Note On Catalog Page.Temperature Limits:20 to 140°F (-6.67 to 60°C). -20°F (-28°C) With Low Temperature Option.Size:4" (101.6 MM) Diameter Dial Face.Mounting Orientation:Diaphragm In Vertical Position. Consult Factory For Other Position Orientations.Process Connections:1/8" Female NPT Duplicate High And Low Pressure Taps - One Pair Side And One Pair Back.Weight:1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).Standard Accessories:Two 1/8" NPT Plugs For Duplicate Pressure Taps, Two 1/8" Pipe Thread To Rubber Tubing Adapters And Three Flush Mounting Adapterswith Screws. (Mounting And Snap Ring Retainer Substituted For Three Adapters In MP & HP Gage Accessories.)Agency Approval:Meets The Technical Requirements Of EU Directive 2011/65/EU (RoHS II). Note: -SP Models Not RoHS Approved.Note: For Applications With High Cycle Rate Within Gage Total Pressure Rating, Next Higher Rating Is Recommended.

Dwyer Maghnehic Gauge in Rengali Odisha
SERIES 2000 MAGNEHELIC® DIFFERENTIAL PRESSURE GAGES
Indicate Positive, Negative or Differential, Accurate within 1%No Power RequiredLow CostUsed in Isolation/ Hospital Environments and Temporary Units (No Power Required)Select The Series 2000 Magnehelic® Gage For a Versatile Low Differential Pressure Gage With a Wide Choice of 81 Models And 27 Options To Choose From. Using Dwyer’s Simple, Frictionless Magnehelic® Gage Movement, It Quickly Indicates Air Or Noncorrosive Gas Pressures--Either Positive, Negative (Vacuum) or Differential. The Design Resists Shock, Vibration, Over-Pressures And is Weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage Option For An Accuracy Within 1% of Full Scale, Located Below in the Product Configurator. Also Included With The –HA Option At No Extra Cost Are a Mirrored Scale Overlay and a 6 Point Calibration Certificate.NIST CALIBRATION Available In Product Configurator.Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Please See Series AT-2000 for ATEX Approved.PRODUCT APPLICATIONSFilter MonitoringAir Velocity with Dwyer Pitot TubeBlower Vacuum MonitoringFan Pressure IndicationDuct,Room or Building PressuresClean Room Positive Pressure IndicationSPECIFICATIONSService:Air And Non-Combustible, Compatible Gases (Natural Gas Option Available).Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Wetted Materials:Consult Factory.Housing:Die Cast Aluminum Case And Bezel,With Acrylic Cover,Exterior Finish is Coated Gray To Withstand 168 Hour Salt Spray Corrosion Test.Accuracy:±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM Ranges), Throughout Range at 70°F (21.1°C).Pressure Limits:-20 in Hg. to 15 PSIG.† (-0.677 bar to 1.034 bar); MP Option: 35 PSIG (2.41 Bar),HP Option: 80 PSIG (5.52 Bar).Enclosure Rating:IP67.Overpressure:Relief Plug Opens At Approximately 25 PSIG (1.72 Bar), Standard Gages Only. See Overpressure Protection Note On Catalog Page.Temperature Limits:20 to 140°F (-6.67 to 60°C). -20°F (-28°C) With Low Temperature Option.Size:4" (101.6 MM) Diameter Dial Face.Mounting Orientation:Diaphragm In Vertical Position. Consult Factory For Other Position Orientations.Process Connections:1/8" Female NPT Duplicate High And Low Pressure Taps - One Pair Side And One Pair Back.Weight:1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).Standard Accessories:Two 1/8" NPT Plugs For Duplicate Pressure Taps, Two 1/8" Pipe Thread To Rubber Tubing Adapters And Three Flush Mounting Adapterswith Screws. (Mounting And Snap Ring Retainer Substituted For Three Adapters In MP & HP Gage Accessories.)Agency Approval:Meets The Technical Requirements Of EU Directive 2011/65/EU (RoHS II). Note: -SP Models Not RoHS Approved.Note: For Applications With High Cycle Rate Within Gage Total Pressure Rating, Next Higher Rating Is Recommended

Dwyer Maghnehic Gauge in Dehradun Uttarakhand
SERIES 2000 MAGNEHELIC® DIFFERENTIAL PRESSURE GAGES
Indicate Positive, Negative or Differential, Accurate within 1%No Power RequiredLow CostUsed in Isolation/ Hospital Environments and Temporary Units (No Power Required)Select The Series 2000 Magnehelic® Gage For a Versatile Low Differential Pressure Gage With a Wide Choice of 81 Models And 27 Options To Choose From. Using Dwyer’s Simple, Frictionless Magnehelic® Gage Movement, It Quickly Indicates Air Or Noncorrosive Gas Pressures--Either Positive, Negative (Vacuum) or Differential. The Design Resists Shock, Vibration, Over-Pressures And is Weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage Option For An Accuracy Within 1% of Full Scale, Located Below in the Product Configurator. Also Included With The –HA Option At No Extra Cost Are a Mirrored Scale Overlay and a 6 Point Calibration Certificate.NIST CALIBRATION Available In Product Configurator.Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Please See Series AT-2000 for ATEX Approved.PRODUCT APPLICATIONSFilter MonitoringAir Velocity with Dwyer Pitot TubeBlower Vacuum MonitoringFan Pressure IndicationDuct,Room or Building PressuresClean Room Positive Pressure IndicationSPECIFICATIONSService:Air And Non-Combustible, Compatible Gases (Natural Gas Option Available).Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Wetted Materials:Consult Factory.Housing:Die Cast Aluminum Case And Bezel,With Acrylic Cover,Exterior Finish is Coated Gray To Withstand 168 Hour Salt Spray Corrosion Test.Accuracy:±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM Ranges), Throughout Range at 70°F (21.1°C).Pressure Limits:-20 in Hg. to 15 PSIG.† (-0.677 bar to 1.034 bar); MP Option: 35 PSIG (2.41 Bar),HP Option: 80 PSIG (5.52 Bar).Enclosure Rating:IP67.Overpressure:Relief Plug Opens At Approximately 25 PSIG (1.72 Bar), Standard Gages Only. See Overpressure Protection Note On Catalog Page.Temperature Limits:20 to 140°F (-6.67 to 60°C). -20°F (-28°C) With Low Temperature Option.Size:4" (101.6 MM) Diameter Dial Face.Mounting Orientation:Diaphragm In Vertical Position. Consult Factory For Other Position Orientations.Process Connections:1/8" Female NPT Duplicate High And Low Pressure Taps - One Pair Side And One Pair Back.Weight:1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).Standard Accessories:Two 1/8" NPT Plugs For Duplicate Pressure Taps, Two 1/8" Pipe Thread To Rubber Tubing Adapters And Three Flush Mounting Adapterswith Screws. (Mounting And Snap Ring Retainer Substituted For Three Adapters In MP & HP Gage Accessories.)Agency Approval:Meets The Technical Requirements Of EU Directive 2011/65/EU (RoHS II). Note: -SP Models Not RoHS Approved.Note: For Applications With High Cycle Rate Within Gage Total Pressure Rating, Next Higher Rating Is Recommended

Dwyer Maghnehic Gauge in Rairangpur odisha
SERIES 2000 MAGNEHELIC® DIFFERENTIAL PRESSURE GAGES
Indicate Positive, Negative or Differential, Accurate within 1%No Power RequiredLow CostUsed in Isolation/ Hospital Environments and Temporary Units (No Power Required)Select The Series 2000 Magnehelic® Gage For a Versatile Low Differential Pressure Gage With a Wide Choice of 81 Models And 27 Options To Choose From. Using Dwyer’s Simple, Frictionless Magnehelic® Gage Movement, It Quickly Indicates Air Or Noncorrosive Gas Pressures--Either Positive, Negative (Vacuum) or Differential. The Design Resists Shock, Vibration, Over-Pressures And is Weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage Option For An Accuracy Within 1% of Full Scale, Located Below in the Product Configurator. Also Included With The –HA Option At No Extra Cost Are a Mirrored Scale Overlay and a 6 Point Calibration Certificate.NIST CALIBRATION Available In Product Configurator.Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Please See Series AT-2000 for ATEX Approved.PRODUCT APPLICATIONSFilter MonitoringAir Velocity with Dwyer Pitot TubeBlower Vacuum MonitoringFan Pressure IndicationDuct,Room or Building PressuresClean Room Positive Pressure IndicationSPECIFICATIONSService:Air And Non-Combustible, Compatible Gases (Natural Gas Option Available).Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.Wetted Materials:Consult Factory.Housing:Die Cast Aluminum Case And Bezel,With Acrylic Cover,Exterior Finish is Coated Gray To Withstand 168 Hour Salt Spray Corrosion Test.Accuracy:±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM Ranges), Throughout Range at 70°F (21.1°C).Pressure Limits:-20 in Hg. to 15 PSIG.† (-0.677 bar to 1.034 bar); MP Option: 35 PSIG (2.41 Bar),HP Option: 80 PSIG (5.52 Bar).Enclosure Rating:IP67.Overpressure:Relief Plug Opens At Approximately 25 PSIG (1.72 Bar), Standard Gages Only. See Overpressure Protection Note On Catalog Page.Temperature Limits:20 to 140°F (-6.67 to 60°C). -20°F (-28°C) With Low Temperature Option.Size:4" (101.6 MM) Diameter Dial Face.Mounting Orientation:Diaphragm In Vertical Position. Consult Factory For Other Position Orientations.Process Connections:1/8" Female NPT Duplicate High And Low Pressure Taps - One Pair Side And One Pair Back.Weight:1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).Standard Accessories:Two 1/8" NPT Plugs For Duplicate Pressure Taps, Two 1/8" Pipe Thread To Rubber Tubing Adapters And Three Flush Mounting Adapterswith Screws. (Mounting And Snap Ring Retainer Substituted For Three Adapters In MP & HP Gage Accessories.)Agency Approval:Meets The Technical Requirements Of EU Directive 2011/65/EU (RoHS II). Note: -SP Models Not RoHS Approved.Note: For Applications With High Cycle Rate Within Gage Total Pressure Rating, Next Higher Rating Is Recommended

DWYER TBU-00 TEMPERATURE TRANSMITTER

Field Selectable, Universal Input, In-Head Mounting

The Model TBU-00 Temperature Transmitter is a high precision temperature transmitter designed to easily mount in most temperature sensor instrument enclosures. The universal input reduces inventory while the micro-USB port facilitates easy configuration, and calibration in the lab or in the field. The versatile TBU model allows for selection and configuration of input type, measurement range, and calibration. The output can be set as either direct 4 to 20 mA, or reverse 20 to 4 mA, through easy to use configuration software.

Product Applications

• Process applications where a 4 to 20 mA signal is required
• Food processing equipment
• Boiler equipment
• Refrigeration equipment

Specifications
Input: Thermocouples J, K, R, S, T, N, E, and B; 2, 3, or 4 wire Pt100 RTD, 2 or 3 wire Pt1000 RTD, 2 wire NTC thermistor, or 0 to 50 mV voltage.
Output: Linearized 4 to 20 mA, 2 wire or 20 to 4 mA loop powered.
Transmitter Type: 2, 3, or 4 wire.
Temperature Limits:- 40°F to 185°F (-40 to 85°C).
Power Requirements: 10 to 35 VDC.
Accuracy: See catalog page.
Temperature Drift: < ±0.16% / 25°C. 
Response Time: 1.6 s, typical.
Weight: 1.4 oz (40 g).
Note: Factory set to Pt100 Ω RTD, 0 to 100°C, direct acting.
Features

• Configurable Measurement Range
• Standard Temperature Sensor Head Enclosure Mounting
• Pt100 connection for 2, 3, or 4 wires

Dwyer MS 121 LCD Magnesense Differential Pressure Transmitter

Output: 4-20 mA,

Range: 0.1", 0.25", 0.5" (25, 50, 100 Pa), Panel Mount

MORE ABOUT THIS ITEM

The Magnesense® Differential Pressure Transmitter is an extremely versatile Transmitter for monitoring pressure and Air Velocity. This Compact Package is loaded with features such as field selectable English or metric ranges, adjustable dampening of output signal, and the ability to select a square root output for use with Pitot tubes and other similar flow sensors. Along with these features, the magnetic sensing technology provides exceptional long term performance and enables the Magnesense® Transmitter to be the solution for a myriad of pressure and flow applications. Transmitter also features push button zero and span. This Reduces Calibration Time Significantly over other Transmitters that utilize Potentiometers, and Lowers Maintenance Time and Costs. The Adjus

Specifications & Description

 

• Accuracy±1% (0.5" & 0.25" WC); ±2% (0.1" WC)
• Max Pressure (in WC)0.5
• Process Connection3/16" hose barb
• Battery Type10 to 35 VDC (2-wire)
• Electrical Connections Screw Terminal
• Output4 to 20 mA
• Media Compatibility Air and inert, Noncorrosive, Nonconductive, Nonexplosive Gases
• DescriptionMagnesense Differential Pressure Transmitter, 0.1/0.25/0.50 "WC Selectable Ranges, 3/16" Barb C