D.P. Engineers

• No Power Required
• Low Cost

• Used in Isolation/ Hospital Environments and Temporary Units (No Power Required)

• Filter Monitoring
• Air Velocity with Dwyer Pitot Tube
• Blower Vacuum Monitoring
• Fan Pressure Indication
• Duct,Room or Building Pressures
• Clean Room Positive Pressure Indication

• Service:Air And Non-Combustible, Compatible Gases (Natural Gas Option Available). Note: May Be Used With Hydrogen. Order a Buna-N Diaphragm. Pressures Must Be Less Than 35 PSI.
• Wetted Materials:Consult Factory.
• Housing:Die Cast Aluminum Case And Bezel, With Acrylic Cover, Exterior Finish is Coated Gray To Withstand 168 Hour Salt Spray Corrosion Test.
• Accuracy:±2% (-HA model ±1) of FS (±3% (-HA ±1.5%) on -0, -100PA, -125PA, -10MM and ±4% (-HA ±2%) on -00, -60PA, -6MM Ranges), Throughout Range at 70°F (21.1°C).
• Pressure Limits:-20 in Hg. to 15 PSIG.† (-0.677 bar to 1.034 bar); MP Option: 35 PSIG (2.41 Bar), HP Option: 80 PSIG (5.52 Bar).
• Enclosure Rating:IP67.
• Overpressure:Relief Plug Opens At Approximately 25 PSIG (1.72 Bar), Standard Gages Only. See Overpressure Protection Note On Catalog Page.
• Temperature Limits:20 to 140°F (-6.67 to 60°C). -20°F (-28°C) With Low Temperature Option.
• Size:4" (101.6 MM) Diameter Dial Face.
• Mounting Orientation:Diaphragm In Vertical Position. Consult Factory For Other Position Orientations.
• Process Connections:1/8" Female NPT Duplicate High And Low Pressure Taps - One Pair Side And One Pair Back.
• Weight:1 lb 2 oz (510 g); MP & HP 2 lb 2 oz (963 g).
• Standard Accessories:Two 1/8" NPT Plugs For Duplicate Pressure Taps, Two 1/8" Pipe Thread To Rubber Tubing Adapters And Three Flush Mounting Adapterswith Screws. (Mounting And Snap Ring Retainer Substituted For Three Adapters In MP & HP Gage Accessories.)
• Agency Approval:Meets The Technical Requirements Of EU Directive 2011/65/EU (RoHS II). 
• Note: -SP Models Not RoHS Approved.Note: For Applications With High Cycle Rate Within Gage Total Pressure Rating, Next Higher Rating Is Recommended

Miniature Low Cost Differential Pressure Gauge Series S-5000

Description
• Mounts in Industry Standard Holes
• Accuracy 5%
• Low-Cost Miniature Size

The Series S-5000 is a low cost, diaphragm operated, differential pressure gauge in a miniature housing. The S-5000 can be used in applications for measuring positive, negative, or differential pressure with an accuracy of 5%. Standard applications include monitoring filter status, duct static pressure, room pressure, fan or blower pressure, paint booths, dust collectors, and cabinet purging along with many others.

Customizing Options Available
MODEL NUMBERS
MODEL NUMBERS Pressure Range Model Number Pressure Range
S-5000-0 0 – 0.5" S-5000-25MM 0 – 25 mm
S-5001 0 – 1" S-5000-50MM 0 – 50 mm
S-5002 0 – 2" S-5000-100MM 0 – 100 mm
S-5003 0 – 3"
S-5005 0 – 5" S-5000-125PA 0 – 125 Pa
S-5010 0 – 10" S-5000-250PA 0 – 250 Pa
S-5000-500PA 0 – 500 Pa
S-5000-1KPA 0 – 1 kPa
S-5000-3KPA 0 – 3 kPa

SPECIFICATIONS
Pressure Limits: 30 PSI (2.067 bar)Media Compatibility: Air and compatible non-corrosive gassesAccuracy: +/- 5% full scale throughout range at 70°F (21°C)Temperature Ranges: 20° to 120°F (-7° to 49°C)Housing Material: Glass-filled nylon, polycarbonate coverProcess Connection: Barbed connections for 3/16" I.D. tubingWeight: 6 oz (170 g)Accessories: Two mounting studs and hex nuts, allen wrench, and panel mounting bracketAgency Approvals: RoHS, CE

Select the Magnehelic® gage for high accuracy and for the wide choice of 81 models available to suit your needs precisely. Using Dwyer's simple, frictionless Magnehelic® gage movement, it quickly indicates low air or non-corrosive gas pressures either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or levelling problems. It's inexpensive, too.

The Magnehelic® gage is the industry standard to measure fan and blower pressures, filter resistance, air velocity, furnace draft, the pressure drop across orifice plates, liquid levels with bubbler systems and pressures in fluid amplifier or fluidic systems. It also checks gas-air ratio controls and automatic valves and monitors blood and respiratory pressures in medical care equipment.

Note: May be used with Hydrogen. Order a Buna-N diaphragm.

Product Applications:

• Filter Monitoring
• Air Velocity with Dwyer Pitot Tube
• Blower Vacuum Monitoring
• Fan Pressure Indication
• Duct, Room or Building Pressures
• Clean Room Positive Pressure Indication

Series 626 & 628 Industrial Pressure Transmitter

Complete Offering of Ranges, Connections and Outputs

The SERIES 626 Pressure Transmitters possess a highly precise 0.25% full scale accuracy piezo-resistive sensor contained in a compact, rugged, NEMA 4X (IP66) stainless steel general purpose housing or cast aluminum conduit housing.

The SERIES 628 Pressure Transmitters are ideal for OEMs with 1% full scale accuracy sensors. The corrosion resistant 316L stainless steel wetted parts allow the Series 626 and 628 transmitters to measure the pressure in a multitude of processes from hydraulic oils to chemicals. The Series 626 and 628 are available in absolute and pressure ranges with a variety of optional outputs, process connections and electrical terminations to allow you to select the right transmitter for your application.

Note: The standard conduit housing (-CH) has been phased out, see the conduit box housing (-CB) for the replacement model.

Product Applications

• Compressors
• Pumping Systems
• Irrigation System Pressure
• Industrial Process Monitoring
• Hydraulic

MORE ABOUT THIS ITEM

Ideal for OEM and process applications where ±1% full-scale accuracy is required. Transmitters feature a stainless steel housing and 316 stainless steel oil-filled sensor. The corrosion-resistant 316L stainless steel wetted parts allow these transmitters to measure the pressure in a multitude of processes from hydraulic oils to chemicals in compressors, irrigation equipment, and process monitoring.

A variety of optional outputs, process connections and electrical terminations are available; contact an Application Specialist for details.

• Output Signal Type: Digital Type
• Material: Metal
• Protection: IP65

Minihelic® II Differential Pressure Gage Series 2-5000
Combining clean design,small size and low cost with enough accuracy for all but the most demanding applications our SERIES 2-5000 Minihelic® II gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 psig.

Product Applications

Room Positive Pressure Sensing
Local Indication on Filter Status
Face Velocity on Fume Hood
Duct Pressures
Cabinet Air-Purging
Medical Respiratory Equipment
Air Samplers
Electronic Air Cooling Systems
Laminar Flow Hoods

DWYER OMEGA Maghnehic gauges in Wholesale Dealers Supplies Maihar Madhya Pradesh
SERIES 2000 MAGNEHELIC® DIFFERENTIAL PRESSURE GAGES Indicate Positive, Negative or Differential, Accurate within 1%
No Power Required

• Low Cost
• Used in Isolation/ Hospital Environments and Temporary Units (no power required)

Select the Series 2000 Magnehelic® Gage for a versatile low differential pressure gage with a wide choice of 81 models and 27 options to choose from. Using Dwyer’s simple, frictionless Magnehelic® gage movement, it quickly indicates air or noncorrosive gas pressures--either positive, negative (vacuum) or differential. The design resists shock, vibration, over-pressures and is weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage option for an accuracy within 1% of full scale, located below in the Product Configurator. Also included with the –HA option at no extra cost are a mirrored scale overlay and a 6 point calibration certificate.

NIST CALIBRATION available in Product Configurator.

Note: May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.

Please see Series AT-2000 for ATEX approved.
California Residents:  Click Here for Proposition 65 WARNING.

PRODUCT APPLICATIONS 

• Filter Monitoring
• Air Velocity with Dwyer Pitot Tube
• Blower Vacuum Monitoring
• Fan Pressure Indication
• Duct, Room or Building Pressures
• Clean Room Positive Pressure Indication

Magnehelic gauge dwyer USA

We are authentic trader, supplier and exporter of Magnehelic Gauge Dwyer USA in Delhi available with following details.

Specifications: Differential Pressure gauge

Make:Dwyer USA

Model:Magnehelic Gauge

Range: Multiple ranges are available

Units: MWC, INWC, PASCAL, KPA

Specifications:

Pressure Range: 0.001MPa-35MPa

Accuracy: 1.6% Color: Silver

Dwyer Digital Differential Pressure Gauge

experience of this domain, we provide clients with the premium quality of Dwyer Digital Differential Pressure Gauge. For regulation and monitoring of pressure of different industrial applications, the offered Dwyer digital differential pressure gauge is used. Simple calibration and thermal stability make the pressure gauge highly demanded.

Features:
Simplifies calibration with its digital push button

• Four button operation reduces set up time
• Easy to use and maintain

Specifications:

• Operating Temp.: -20~+70 Oc
• Measuring Range: Medium-pressure Gauge
• Accuracy: 0.25

• Pressure Range: 0-100Mpa
• Color: Silver
• Diameter:100mm

The Series WDG Weatherproof Digital Pressure Gage measures gas and liquid pressure with high accuracy at an affordable price. It’s rugged weatherproof design stands up to outdoor and industrial environments. The 4-digit backlit display with four selectable units makes readings easily visible to prevent reading errors. The WDG comes with 304L stainless steel wetted material for a wide range of compatible liquids and gases.

We are in the process of discontinuing this series, the suggested replacement is Series DPGA/DPGB.

• Pneumatic
• Draft measurement
• Filter monitoring
• Industrial
• Outdoor
• HVAC roof-top
• Flow